If the FortiSwitch management port is used for a layer-3 connection to the FortiGate unit, the FSI can contain only one FortiSwitch unit. That was so in 5.4. 03:48 AM, Created on The NTP server must be reachable from the FortiSwitch unit. If you are configuring a logical interface, you can select from the following options: Specify the IP address and CIDR-formatted subnet mask, separated by a forward slash ( / ), such as 192.0.2.5/24. See, Create a scheduled task for a CLI configuration to be applied to a device group. Dotted quad formatted subnet masks are not accepted. Created on Nowadays most switches can do that with a separate VLAN. Maximum missed LCP echo messages before disconnect. For the subnet and mask -- I understood what you mean. We recommend this option instead of HTTP. Configure FortiLink on any physical port on the FortiGate unit and authorize the FortiSwitch unit as a managed switch. Use the following command to enable or disable multiple FortiLink interfaces. Seconds the system waits before it retries to discover the PPPoE server. You shouldn't rely on one of FGTs to route/NAT your access. 12:40 AM. No layer-2 data path component, such as VLANs, can span across layer 3 between the FortiGate unit and the FortiSwitch unit. When setting up a new environment where it's safe to test it's another story. I guess if that "gateway" field would work also for incoming traffic so that that separate mgmt network would be behind certain existing interface then maybe it would work. For ha-direct, I understood now, thank you. The default is 3. Usually the gateway should be in the same subnet, not in some other. Copyright 2023 Fortinet, Inc. All Rights Reserved. You use the HA node IP list configuration in an HA active-active deployment. 07-04-2022 This site uses Akismet to reduce spam. If you are editing the configuration for a physical interface, you cannot set the type. LCP echo interval in seconds. But for the console access: it already works the way you described (via a serial/console switch). Edited on Thank you for the explanation. You have at least four FGT devices in multiple clusters. Fortinet recommends using the FortiGate GUI because the CLI procedures are more complex (and therefore more prone to error). PPPoEUse PPPoE to retrieve a configuration for the IP address, gateway, and DNS server. The IP address must be on the same subnet as the network to which the interface connects. 04:51 AM, - if you configure an HA management interface, this interface is technically considered to be in a different (hidden) VLAN, -> the HA management interface does NOT use the same routing table/local-in policies/other interface configuration you may have in place, -> setting the gateway in the management interface (this is in the HA configuration; worded a bit confusingly, I agree) essentially tells the FortiGate what gateway to use for traffic from the HA interface, -> this can be with specified subnets (FortiGate will have routes to the subnets via the HA management interface and defined gateway), or essentially a default route via the HA interface; these settings (gateway/specified subnets) are only used for HA management traffic. This modifies the network devices behavior as long as those commands are in force. If overlapping of subnets is not allowed, it can't be in the same unit/VDOM if it is meant to be a real address. Type a valid administrator name and press Enter. 07-10-2012 NOTE: The NTP server must be configured on the FortiSwitch unit either manually or provided by DHCP. See Add or modify a configuration. I don't use these separate IP's for sending out SNMP or other stuff but if I did then I'm not sure how the Fortigate really handles this. This article describes how to check the corresponding CLI configuration when the FortiGate is configured in web GUI. If you have an existing subnet/VLAN dedicated to device management, for example, you might want to put the FortiGate HA interfaces into this. So I removed the route, put back NAT in the firewall rule, changed the VLAN interface's IP back to the one it was before, that is, in the same subnet where those mgmt IP's are and got back the mgmt to different mgmt IP's like that -- as it was before. to indicate the destinations that should use the defined gateway. 07-22-2012 When using user/host profiles to determine Access Policies, use location criteria to group devices with common CLI capabilities. 07-01-2022 The following limitations apply to FSIs operating in FortiLink mode over a layer-3 network: To configure a FortiSwitch unit to operate in a layer-3 network: config switch-controller global set ac-discovery dhcp set dhcp-option-code
fortigate interface configuration cli
You must be sibley county warrant list to post a comment.